Mindat Logo
bannerbannerbannerbanner
Welcome!

Just a tip about polishing Selenite.

Posted by Bri Dragonne  
avatar Just a tip about polishing Selenite.
January 14, 2011 11:58PM
nl    
I had a cleaved section of Selenite with Copper dendrite inclusions that I needed to polish recently so I could show the inclusions.

Please, do NOT use this technique on your fave specimen! It worked for me but I take no responsibility, etc etc. :)

The section had been cleaved and was shiny at one time, but over various handlings, it had become rather scratched.

So, several compounds and no luck later, I remembered that Selenite dissolves in water...

I then ran hot water from the tap over it (Slowly heating the water so that it didn't get shocked, the specimen I mean) and then cooling the water and flinging the excess off.

I ran the water over it for about 15 minutes and amazingly, there was a super shiny finish with interesting patterns on it.

This is just a tip for if anyone else does a search like 'How to polish Selenite' :)

-Bri



Edited 1 time(s). Last edit at 01/15/2011 12:49AM by Bri Dragonne.
avatar Re: Just a tip about polishing Selenite.
January 15, 2011 06:47PM
Brilliant Bri!
avatar Re: Just a tip about polishing Selenite.
January 15, 2011 10:47PM
pe    
photo? too bad there wont be a before and after would be neat to see

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
A buena hambre no hay pan duro
avatar Re: Just a tip about polishing Selenite.
January 16, 2011 12:46AM
nl    
I will scuff it up a bit (Easy to do) and make a before and after photo ;)


-Bri
Beth
Re: Just a tip about polishing Selenite.
May 15, 2012 03:21PM
Not sure if anyone is still checking this thread, but I came upon it looking for a way to restore the polish to a piece of selenite. I had gotten a polished selenite palm stone and in trying to get the stickiness from the price tag off, I used water, dish soap, and when that didn't work, water and goo gone. The process took the polished finish off the entire piece. I was since told you shouldn't use water with selenite, and a rock shop said they could buff it for me (they are kind of out of the way to get to, and it would cost about the same as what I paid for the stone originally.)

I'm a little leary of doing anything more with water since that seemed to have ruined the finish to begin with. Is there a link to the before/after photos? And are there any more specific details such as how long you ran hot water over it before changing to cold water, etc...?

Otherwise, are there any other suggestions out there for polishing selenite.

Thanks much!
avatar Re: Just a tip about polishing Selenite.
May 15, 2012 05:37PM
I have not tried the hot water polishing but in the past I did some sculptures from selenite. I got a good polish by hand using soft leather and Aluminum oxide polish paste after sanding with 600 grit or finer. I have also used lately ZAM on a soft cotton buff wheel on my polishing motor.
avatar Re: Just a tip about polishing Selenite.
May 16, 2012 07:48AM
How big was the polished piece of selenite. Is it really a crystal of gypsum or of the satin spar variety? It it is not too big you might try putting it in the water reservoir of your toilet for a couple of days.

Rock Currier
Crystals not pistols.
Re: Just a tip about polishing Selenite.
May 16, 2012 09:56AM
it    
In my experience washing gypsum crystals with water (even cold for a short time) removes the luster and ruins the specimen, I don't think there is a way to recover it, alcohol is ok.
Beth
Re: Just a tip about polishing Selenite.
May 20, 2012 01:24PM
Thanks everyone.. Note to Rock Currier -- it's a palm sized piece and maybe satin spar-- when it was polished it reminded me of satin. It looks very similar to what is pictured here at the following website, though mine maybe wasn't quite as translucent as the ones pictured: [www.curiogrove.com] (I did not get this from this site). It's representative of its size as well. But I also got an e-mail from someone who said that selenite loves water-- just not being submerged in it. It will dissolve if submerged.

I don't have any buffing tools-- and it's sort of sounding like hand buffing won't quite cut it. The stone is still smooth-- just no longer polished.

Thanks all for the comments and suggestions. I will check back periodically to see if anything else is posted...
avatar Re: Just a tip about polishing Selenite.
May 23, 2012 05:58PM
I have used a soft cloth or soft leather impregnated with a polish compound usually Aluminum Oxide but Cerium Oxide would do. I think a soft leather of chamois worked better and it does take a little while and a lot of elbow grease although a buffing wheel does a better job. The piece may look smooth but it may be best to sand it with 600 grit and even down to 1000 grit sandpaper first. You might want to start with 1000 grit since it may have be polished previously and just gotten etched. You can usually find really fine grit silicon carbide sand paper at an auto parts store. You have to do it with a little water as well or the sand paper clogs up to fast and it is dusty. Gypsum does dissolve in water but very slowly in cold water. When I use to do gypsum sculptures using mostly satin spar, I would have a pan with a little water in which I set the piece in and dipped the sandpaper in and out of the water as I sanded. This keeps the dust down, the piece clean and the sandpaper doesn't clog up too fast. The piece isn't submerged just setting in the water or held near. The polish is done with a slurry of polish compound.
Re: Just a tip about polishing Selenite.
June 11, 2012 06:28PM
I have a question as well. Yesterday I went with the Colorado Mineral Society to a dig site at the Denver International Airport, who one of the members is the excavation manager so we had permission to collect. I found and dig so much Selenite that it was weighing down my car, I have really clear crystals, a couple giant plates that I chiseled off sand stone boulders, and some large ones completely covered in clay and mud. A lot of the plates have thin crystals cover in mud, I cleaned a couple of really nice small pieces under running water with dish soap. They still show clay and some of the cracks, what would be the best way to clean the big fragile plates without breaking things and getting the rest fully clean?

Thanks Aaron,
avatar Re: Just a tip about polishing Selenite.
June 11, 2012 08:34PM
Buy one of the little high pressure fabric guns and this will solve a lot of your cleaning problems. Read the soap and water section of Cleaning Quartz. [www.mindat.org]

Rock Currier
Crystals not pistols.
avatar Re: Just a tip about polishing Selenite.
June 11, 2012 08:49PM
lv    
Thanks! I have some interesting satin spars (including ones with celestite cones and wave ripples), unfortunately some of my best pieces, which I collected 14 years ago from locality which is no longer accessible, have got some damages. I will first start with some not so good pieces and maybe make some pictures with results.
Re: Just a tip about polishing Selenite.
June 11, 2012 09:17PM
Awesome, thanks rock! I'll post some pictures when I get them clean because I don't see this location anywhere on here, maybe because it's private property and only people with someone who works there can go and dig?
avatar Re: Just a tip about polishing Selenite.
June 11, 2012 09:43PM
lv    
Before and after 30 minutes under running warm tap water. Most of damages are gone, except for some major ones. Specimen looks kinda shiny now.
Attachments:
open | download - P1012469 (Medium).JPG (87.1 KB)
open | download - P1012472 (Medium).JPG (101.3 KB)
Author:

Subject:


Attachments:
  • Valid attachments: jpg, gif, png, pdf
  • No file can be larger than 1000 KB
  • 3 more file(s) can be attached to this message

Spam prevention:
Please, enter the code that you see below in the input field. This is for blocking bots that try to post this form automatically. If the code is hard to read, then just try to guess it right. If you enter the wrong code, a new image is created and you get another chance to enter it right.
CAPTCHA
Message:

Mineral and/or Locality  
Search Google  
Copyright © Jolyon Ralph and Ida Chau 1993-2014. Site Map. Locality, mineral & photograph data are the copyright of the individuals who submitted them. Site hosted & developed by Jolyon Ralph. Mindat.org is an online information resource dedicated to providing free mineralogical information to all. Mindat relies on the contributions of thousands of members and supporters. Mindat does not offer minerals for sale. If you would like to add information to improve the quality of our database, then click here to register.
Current server date and time: April 23, 2014 16:59:10
Mineral and Locality Search
Mineral:
and/or Locality:
Options
Fade toolbar when not in focusFix toolbar to bottom of page
Hide Social Media Links
Slideshow frame delay seconds